Two FlameTech Plumbing & Heating team members beside a FlameTech service van
5-star Google rated

Silverado Plumbers Calgary: Plumbing and Heating for Homes Built Since 2001

5.0· 100+ Google reviewsRed SealAlberta LicensedBBB Accredited

If you need a plumber in Silverado, Calgary, the house in question is almost certainly a young one. The City's 2021 community profile counts 2,490 of Silverado's 2,545 occupied homes, or 98%, as built in 2001 or later. Whatever is still original to those houses, whether that's the furnace, the water heater or the taps, has been in service for somewhere between about five and 25 years, and the right advice changes a good deal depending on which end of that range your home falls at. On our team, Red Seal journeyman plumbers take care of water lines, fixtures and drains, while Alberta-licensed gas fitters look after furnaces, gas water heaters and the gas piping running to them.

Silverado is in the SW quadrant, and the Federation of Calgary Communities places it south of Somerset and Shawnessy. Stoney Trail forms its northern edge, Macleod Trail its eastern edge and 194 Avenue SW its southern one, while Spruce Meadows Way SW on the west side doubles as the city limit. North across Stoney Trail lies Somerset, with Shawnessy beside it toward the east end. Chaparral is over Macleod Trail on the SE side of the city, and Belmont and Yorkville sit south of 194 Avenue. At the 2021 census, 7,975 residents lived here in roughly 2,550 households.

Three homes in four are single-detached houses: 1,915 of them, where Calgary as a whole sits at 55%. Row houses account for 12% (the city figure is 10%), semi-detached homes for 6% and units in low-rise apartment buildings for 5%. Owners occupy 87% of homes, against 69% citywide. Our SW Calgary plumbing page covers the surrounding communities.

Before you phone, it's worth noting the year the house went up and what exactly is going wrong; between them, those two details rule a lot out. We dispatch from both Calgary and Airdrie, and quotes are free. Call 587-834-3668 and we'll tell you honestly when we can get there.

Hot Water for Bigger Households, First Furnace Decisions and Hard Water in Silverado
25+
Years in the trade
5.0★
Google rated
FREE
Quotes
Licensed
and insured

Hot water giving out before everyone has showered, or a furnace you're unsure about? The quote is free: call 587-834-3668 and we'll tell you honestly when we can get there.

Call 587-834-3668
via Google

“I have been lucky enough to have Shaun as my go to plumber for many years. He has always been knowledgeable, he finds the problem and fixes it, he’s honest and great to work with. I am so excited that he and Jason ( also awesome) have teamed up to offer the best service around.”

Cindy Luntley — verified Google review for FlameTech

Cindy Luntley

Calgary · 1 year ago

Nearly every Silverado home dates from 2001 or later

The City's 2021 profile puts 1,450 of the 2,545 occupied homes in the 2001 to 2010 bracket, 720 in 2011 to 2015 and 320 in 2016 to 2021. That leaves just 55 older houses: 35 from 1991 to 2000, 10 from 1981 to 1990 and 10 from 1960 or before, with none at all from 1961 to 1980. Citywide, the 2001 to 2010 decade holds 20% of homes and the years since 2011 hold 18%, so Silverado's housing is much younger than Calgary's as a whole. Young isn't the same as trouble-free. A house finished in 2003 has run more than two decades of hard water through any fixture nobody has changed, and the oldest equipment in the community is now well into the age where repair-or-replace questions come up.

Poly-B: a question for a handful of houses

Poly-B is grey plastic water supply pipe, fitted in homes from about 1978 into the mid-1990s. With only 55 Silverado homes older than 2001, very few owners here need to think about it. If yours is one of the older ones, or you don't know the year, check the lines coming off the water heater and any supply lines visible in an unfinished basement ceiling. Grey plastic is what you're looking for. Do I need to replace Poly-B? walks through identifying it and deciding whether to act. A Poly-B repipe costs $3,500 to $7,250 at September 2026 prices.

Builder-installed taps, toilets and shut-offs

The kitchen tap or toilet that came with a 2004 house has been handling hard water every day since. The signs it's wearing out are familiar: a spout that keeps dripping however firmly you close the handle, a toilet that tops itself up every so often with nobody near it, a shower that drifts hot and cold. Plenty of those come down to a cartridge or a fill valve rather than a whole fixture, and we'll tell you when that's all it needs. The shut-off under the sink deserves a look too, because a valve nobody has turned in years can stick, or start to seep once it finally moves. Faucet installation and replacement covers taps, toilet repair deals with running and leaking toilets, and a new toilet is quoted on site through toilet installation.

Furnaces from either side of the 2009 efficiency rule

Under Canada's energy efficiency regulations, a gas furnace without built-in cooling manufactured on or after December 31, 2009 has to reach at least 90% annual fuel utilization efficiency (AFUE); before that, the minimum was 78%. From July 3, 2019 the bar for most of those furnaces went up to 95%, with lower floors for some categories. Silverado's two building waves land on either side of the 2009 change: 57% of homes went up in the decade that ended as the 90% rule took hold, and 41% came after it. A house from 2006 could have been handed either a mid-efficiency furnace or a high-efficiency one, depending on what the builder chose. A furnace made for a 2013 house would normally have had to meet the 90% minimum.

Checking the vent

You can tell the two types apart without removing a single panel. Follow the exhaust pipe from the top of the furnace. If it's metal and runs up through the house toward the roof, the furnace is mid-efficiency. If it's plastic and leaves through a side wall, with a small tube carrying water off to a floor drain or condensate pump, it's a condensing high-efficiency model. That trickle of water is normal; a pool of it on the floor around the cabinet is not, and why is my furnace leaking water? runs through the usual reasons. Moving up to high-efficiency takes plastic vent pipe run out through a wall and a drain route for the condensate. If a gas water heater used to share the old metal flue with the furnace, it can end up venting on its own into a flue that was sized for two appliances, and our gas fitter checks that it still vents safely before the job is closed out. That check is not homeowner work. Leave anything on the gas or venting side to a licensed gas fitter.

Repair or replace

Age gets the conversation started; it doesn't settle it. A 2015 high-efficiency furnace with one failed component is usually a furnace repair, and we'll say so when fixing it is the sensible choice. A 2003 mid-efficiency unit that needs a costly part is a different discussion. If you do replace it, the new furnace should be sized to the house as it is now, taking in its insulation, windows, air leakage and Calgary's design temperature, not matched to whatever the old badge says. A basement developed after move-in, or replacement windows, can shift what the house really needs. We're an authorized AirEase dealer, and a furnace replacement runs $4,500 to $9,600 at September 2026 prices. Furnace replacement cost in Calgary explains what pushes a job toward either end.

Adding cooling at the same time

Ducted cooling uses the furnace's blower and ductwork, which makes a furnace replacement the natural moment to plan it. A heat pump cools the house through summer and does the heating in milder weather, then hands over to the gas furnace once it turns properly cold. At September 2026 prices it's $6,200 to $8,800, and heat pump cost in Calgary goes through where that money goes. For a single hot bedroom or a top floor, a ductless mini split needs no ductwork changes and costs $3,500 to $5,000. Central air conditioning gets priced once we've seen the house.

Hot water for three-, four- and five-person households

Silverado households average 3.1 people, where Calgary's average is 2.6. Four-person households make up 26% here (city: 16%) and those with five or more another 15% (city: 10%), so 41% of homes hold at least four people, compared with 26% across Calgary. A quarter of residents are under 15, and 59% of census families are married couples with children, against 44% citywide. People living alone account for just 13% of households, half the city's 26%. All of that adds up to showers, laundry and dishwasher cycles stacked one after another, mostly in the same early-morning and evening rush.

Choosing the tank size

Your current tank's capacity is printed on its label. If it kept up when the children were small and now goes lukewarm before the last person is through the shower, the answer is usually a bigger tank rather than a repair. At September 2026 prices, replacing with an atmospheric tank costs $1,950 for 40 gallons, $2,100 for 50, $2,450 for 60 and $2,990 for 75. Power-vent tanks are quoted on their own. Hot water tank replacement describes the job, and our hot water tank replacement cost guide breaks the figures down. Water pooling at the base is a separate issue with its own page: leaking water heater. For flushing and servicing, follow your model's manual, bearing in mind how hard the local water is.

Tankless: endless, but with a flow limit

With a tankless water heater, water is heated as it flows through, so it never runs dry the way a tank does. What it can't do is heat an unlimited amount at one moment, and two showers running alongside the dishwasher may ask for more than it can deliver at full temperature. At September 2026 prices it's $5,400 to $6,500. Hard water leaves scale inside the heat exchanger, which has to be descaled by a technician on the schedule set out in your model's manual. If your existing tank is sound and simply too small, a larger tank is the cheaper way out. Tankless vs tank water heaters in Calgary lays out how the two compare.

Glenmore water and the scale it leaves

The City's water quality page describes the supply this way: "Residents in the south receive most of their water from the Elbow River through the Glenmore Water Treatment Plant." That makes Glenmore the likely source for most Silverado homes, though the City doesn't promise it for every street. Glenmore's 2025 hardness readings, in mg/L as calcium carbonate, ran 208 to 274 in the first quarter, 181 to 245 in the second, 191 to 216 in the third and 213 to 248 in the fourth, and the City notes hardness is usually highest between December and February. Water that hard leaves white crust on taps and shower glass, coats the inside of kettles, and builds up out of sight in the water heater and dishwasher.

Softener, RO or both

The two deal with different things. A water softener treats every drop entering the house, pulling out the calcium and magnesium that cause scale, which protects the water heater, appliances and fixtures; at September 2026 prices it's $2,250 to $3,050. A reverse osmosis system filters water at one tap, usually in the kitchen, to supply drinking and cooking water; it costs $780 to $1,440. Some households want both. The City points out that the calcium and magnesium in hard water have no known health effects, and that salt-based softeners may not be right for anyone on a sodium-reduced diet, so raise it at the quote if that applies. Water softener vs reverse osmosis matches each system to the problem it solves.

Row houses, semi-detached homes and shared walls

About one Silverado home in four isn't a detached house. The 2021 profile counts 305 row houses, 155 semi-detached homes, 135 units in low-rise apartment buildings (under five storeys) and 30 duplex flats. It also counts 330 renter households, 13% of the total, well below the city's 31%.

Finding whose pipe is leaking

When water appears on a shared wall, or on a ceiling below the home next door, the stain often isn't sitting right under the leak. Water runs along framing and drywall before it shows. Cutting into walls on a hunch costs money and can start a dispute over who pays. Leak detection finds where the water is actually coming from, so the repair lands on the right side of the wall.

Renters, condo owners and shared lines

Tenants should go to the landlord or property manager first instead of hiring a plumber themselves. In a condo complex, the bylaws and condominium plan draw the line between pipes you own and pipes the corporation owns, and the property manager can usually say which side a given line falls on. If you own half of a semi-detached house and the line in question serves both halves, sort it out with the neighbour before anyone books the work.

Main drains, sewer backups and sump pumps

If sewage comes up a floor drain

Keep everyone out of the area, then call 311. The person who answers helps work out whether the trouble probably sits on your property or in the City's own system; if no City inspection is needed, a plumber is the next call. Your insurer should hear about it too. When the blockage turns out to be on your side, we clear the main drain, run a camera along it to see what caused the backup, and hand you the recording. Repairing, lining or digging up sewer pipe isn't work we take on, so if the camera finds a break or a sag, that footage goes with you to a sewer contractor. Drain cleaning has more on clearing a main line.

Backwater valves

The City recommends a backwater valve wherever a home has plumbing below ground level, such as a basement toilet, shower or floor drain. The valve lets wastewater out as usual and shuts if sewage starts flowing the wrong way. Some houses already have one, under a removable cover in the basement floor, generally close to where the main drain exits, so look before assuming you need to add it. Where a new valve can sit depends on how the pipes under the slab are laid out, which is why we price it after seeing the basement. Backwater valve installation explains the work, and backwater valve installation cost in Calgary covers the budget.

Failed sump pumps get replaced

Not every house has a sump pit. If yours does and the pump has quit, we replace it rather than repair it. At September 2026 prices, a ProFlo 1/2 HP pump in the pit you already have is about $504, and a new pit fitted with a pump is about $2,000. Sump pump installation covers the job, and if the pump runs nonstop instead of not at all, see why does my sump pump keep running?

How we work

Simple, honest, on your schedule.

01

Call or request a quote

Tell us what's going on. We listen first and ask the right questions before we schedule anything.

02

Free written estimate

We assess the job and give you an all-in price in writing. No pressure, no surprise add-ons.

03

Book the work

We give you a realistic booking date up front and confirm it with you before the day.

04

Clean, code-compliant service

Licensed technicians complete the work to Alberta code, clean up, and walk you through what we did.

Request Service

Get a free Silverado plumbing or heating quote.

Tell us what's going on and our dispatch team will call you back with pricing and availability.

We call you back — urgent jobs, call us directlyWe never share or sell your info

Or call 587-834-3668 if it's urgent

When you're ready

Book a Red Seal plumber in Calgary.

Free estimates and upfront pricing, from local technicians who treat your home like their own.

Free estimate · No service charge for quotes · BBB Accredited