Water6 min read

How to Replace Reverse Osmosis Filters

How to replace reverse osmosis filters: match cartridges to your model, depressurise and flush as your manual says, and treat the membrane as its own job.

How to replace reverse osmosis filters depends on which cartridges you mean. Changing the pre- and post-filters is routine upkeep; replacing the membrane is a separate job with its own handling and flushing rules. For both, your system's manual decides how it's done, because brands disagree on shut-off, flushing and sanitising.

Find your model and its manual

Find the brand and model on the unit or its paperwork, get that model's manual, and note the part numbers on the cartridges already in it. Fitting the housing doesn't make a cartridge right. Pentair's Everpure PRO manual says a replacement membrane "should be with one of identical specifications, as defined by the manufacturer". Health Canada says the same in general terms: "consumers are reminded that they should carefully follow the maintenance instructions included with the device".

Identify the filter stages

Pre-filters

Usually a sediment filter and one or more carbon filters, catching grit and chlorine before they reach the membrane. They exist to protect it, so a late change puts the membrane at risk.

The membrane

The part that does the reverse osmosis, in its own housing (often a horizontal tube). It usually outlasts the pre-filters.

Post-filters and add-on cartridges

After the storage tank, many systems have a polishing carbon filter for taste. Some add a remineralising cartridge. Count your stages before ordering.

Housings differ as well: wrench-opened canisters on the APEC RO-90 and Everpure PRO, twist-off cartridges on the Waterdrop G3, twist-lock cartridges on Aquasana.

How often: your manual's schedule, not a general one

Each manufacturer gives figures for its own model, and they don't agree.

ModelWhat the manufacturer says
APEC RO-90"Stages 1, 2, 3 Pre-Filters: Replace every 12 months." The same manual says to change them "at least every 6-12 months". Membrane on city water: "Replace every 3-5 years depending on input water quality, water usage, and prefilter change maintenance".
Pentair Everpure PROPrefilter "every 3 months, or earlier if your water is highly turbid, and when changing the membrane". "The Membrane (PRO) should be replaced every 12–24 months."
Waterdrop G3CF filter "6 months or 550 gallons", RO membrane "24 months or 2200 gallons", CB filter "12 months or 1100 gallons".
Aquasana AQ-SFROCarbon blocks every 6 months; SmartFlow membrane every 12 months.
Kinetico K5"replace the prefilter and postfilter cartridges annually or upon system shutoff, whichever occurs first."

These don't transfer between brands. Check your manual.

Signs a change is due

  • Taste, smell or colour changes. Everpure: "Changes in taste, odor, and color of the filtered water indicate that the cartridge(s) and/or membrane should be replaced".
  • Slower flow at the RO faucet, or leaks. Culligan lists "Lower flow rate, lingering taste or odor, leaks or changes in system performance".
  • An indicator light, on units that have one. Waterdrop: "Be sure to reset the filter life indicator every time you replace your filter."
  • A boil-water advisory. Kinetico says filters may need changing "in the event of a boil order or other events that can compromise your filters."

Why your water matters

The City of Calgary says "The hardness of Calgary's water varies seasonally and by location", and Aquasana says "Membrane life depends on pH and supply water hardness." Weighing a softener against RO? See water softener vs reverse osmosis.

Replacing the pre- and post-filters

Shut off and depressurise the way your manual says

The system, storage tank included, holds pressure. Kinetico says the K5 "must be properly depressurized before attempting to remove any cartridge or other component." APEC's sequence for the RO-90: "Turn OFF cold water supply to RO system. Turn OFF tank ball-valve. Turn on the RO faucet lever to relieve the built-up pressure inside the RO system."

Not every unit works that way: Waterdrop says its G3 filters "could be replaced directly without cutting off power and water". Whichever yours is, put a towel and a shallow pan under the housings first.

Swap the cartridges

  • One stage at a time, so each new cartridge goes where the old one came out.
  • Check the flow-direction marking on the cartridge or housing.
  • Inspect the O-ring. Everpure: "It is important that the o-ring be properly seated in the groove below the threads of the housing or a water leak could occur." APEC recommends replacing it "every year or when replacing the 3 pre-filters."
  • Tighten the way the manual says. Everpure: "HAND-TIGHTEN ONLY."

Flush the new filters

New carbon sheds fine black dust, so the first water through needs to go down the drain. Everpure says to "drain one full tank to flush the carbon fines out of the system." APEC's restart has you keep the tank valve closed, turn the supply and RO faucet back on, and "let purified water run for 10-15 minutes to relieve built-up pressure inside the RO unit."

Check for leaks

APEC: "Check for leaks!" Go over every housing, fitting and tube under pressure, and again once the tank refills. Aquasana's AQ-RO-3 membrane replacement sheet says to "allow 2 hours for pressure to build up in the system & check for leaks."

Replacing the membrane is a separate job

Many manuals pair it with a filter change. Everpure: "When installing a new membrane, it is recommended that you also replace the prefilter and post-polishing filter cartridges." The membrane needs more care than a cartridge:

  • Orientation. APEC: "Make sure the “double-ring” end of the membrane goes into the housing first".
  • No bare hands. APEC: "Avoid touching the Membrane with your hands to prevent contamination!"
  • No squeezing. Everpure: "do not squeeze it, as this will damage the membrane’s effectiveness."
  • No bleach. APEC: "Do not apply chlorine/ bleach in any way to Membrane for it will damage the membrane!"

New membranes carry a preservative, and flush times vary widely. APEC says to "Drain the first tank of water (through faucet) to flush out the new membrane!" Waterdrop says to "Turn on RO faucet to flush for 30 minutes." Culligan's Aqua-Cleer guide calls for a "Minimum 24 hour flush to remove preservative solution". Don't drink it in the meantime; Waterdrop: "The water is not drinkable during the flushing."

Not every membrane is a routine part. Kinetico says of the K5 membrane: "It is not a FlexFilter and does not need to be replaced regularly like FlexFilters."

Sanitising: only when your manual calls for it

Manuals disagree most here. Everpure: "It is recommended that you sanitize the system each time you change the membrane. It is not necessary to sanitize the system when changing only the prefilter or post-polishing filter cartridges." Culligan: "it’s recommended to do a full system sanitization each time you do a filter change." APEC: "The best time to do this is when you are changing your filters, preferably all 5 filters."

Who does it differs too. The Aqua-Cleer guide: "It is recommended to have your local Culligan dealer perform the sanitization process." Kinetico says that if you change K5 cartridges yourself, "you must use a sanitization kit available from your Kinetico dealer".

Use only the product and amounts your manual gives, on their own. Health Canada: "Never mix household chemical products together." And: "You should never mix bleach products with other cleaning products because this can produce toxic gas."

Leave these to a technician

  • The feed-water adapter or saddle valve on the cold line, and the drain saddle.
  • The RO faucet and any air gap.
  • Anything electrical on units with a booster pump or a tankless design.
  • A leaking manifold. Aquasana's manual tells owners not to take it apart.
  • A leak that comes back after you've reseated the O-ring and retightened the housing.

When to call

If the system is due for replacement rather than another set of cartridges, call 587-834-3668. We install reverse osmosis systems in Calgary and in Airdrie for $780–$1,440 as of September 2026, the same in both cities. Quotes are free, and we give you a price before any work begins. We dispatch from both Calgary and Airdrie; call and we'll tell you honestly when we can get there, or describe your system on our contact page.

Keep reading

Related articles

When you're ready

Book a Red Seal plumber in Calgary.

Free estimates and upfront pricing, from local technicians who treat your home like their own.

Free estimate · No service charge for quotes · BBB Accredited