Furnace repair cost in Calgary comes down to one thing nobody can tell you over the phone: what actually failed. A no-heat call might need a quick cleaning or a major component, which is why there's no price list on this page. Quotes are free, and we price the repair before any work starts, so you decide with a real number in front of you. For how a repair call runs, see furnace repair in Calgary.
What makes up a furnace repair cost
Every repair bill is built from three parts:
- Finding the fault. Watching a start-up, reading any error code, and testing the suspect part instead of guessing.
- The part, if one is needed. Some faults don't need one.
- Labour to fit it, then run the furnace long enough to confirm the fix holds.
Whoever you call, ask before they arrive whether the visit itself is charged.
The fault decides most of it
Repairs fall into rough tiers, and which one your fault lands in matters far more than the name on the cabinet.
Cleaning and settings
The cheap end. A flame sensor coated in carbon stops seeing the flame, so the furnace lights and shuts down seconds later; cleaning it often fixes the problem with no part at all. A badly clogged filter can trip the high-limit switch and cause a similar on-off pattern. A thermostat is worth ruling out too: a wrong setting or a dead battery can look like a furnace fault.
For a furnace that keeps turning off or a thermostat that might be bad, those guides cover what's safe to check first. A furnace blowing cold air is sometimes just the thermostat fan left on ON.
Small parts
A real part, but a modest one, and usually quick to fit.
- Hot-surface igniter. It glows to light the gas. When it fails, you hear the inducer start and nothing lights.
- Capacitor. Gives the blower motor its starting kick. When it goes, the motor hums and won't turn, which is how a cheap capacitor gets mistaken for a dead motor and the far dearer motor gets replaced. See furnace blower issues.
- Limit switch. Shuts the burner off when the furnace runs too hot. Sometimes the switch has worn out; sometimes poor airflow is the real problem.
- Pressure switch. Confirms the vent is clear before the burner fires. A failed switch, a cracked hose and a blocked vent all stop the furnace, and only one of those needs a new switch.
If the furnace is dead rather than misbehaving, start with a furnace that won't turn on.
Major components
The expensive end:
- ECM blower motor. The variable-speed motor on many newer furnaces has its controller built in, which makes it one of the dearest parts in the cabinet.
- Inducer motor. The fan that pushes exhaust out through the vent.
- Control board. A failing board causes odd, inconsistent symptoms, so it gets blamed for faults it didn't cause. It should be tested before anyone orders one.
- Gas valve. Gas-side work is done by our Alberta-licensed gas fitters.
A gas smell isn't a pricing question: if you smell gas, leave the house first and call from outside.
Not a repair at all
A cracked heat exchanger. The heat exchanger keeps combustion gases apart from the air the furnace blows through your house, and a crack can let carbon monoxide into that air. It can't be safely patched. The fix is a new furnace, whatever its age.
What else moves the price
Age and type of furnace
Parts for some older models are discontinued, and an original control board can be hard or impossible to find. Universal parts cover a lot of igniters, sensors and switches, but not everything.
Under the federal Energy Efficiency Regulations, the minimum AFUE for most household gas furnaces was 78 percent for those made from 1995 until December 31, 2009, 90 percent from then until July 3, 2019, and 95 percent for those made since. So a mid-efficiency furnace on a metal flue in an ordinary Calgary house was most likely built before 2010. A condensing furnace has parts a mid-efficiency one doesn't, like a condensate trap and drain. See high-efficiency furnaces for how they work.
Manufacturer warranty
A warranty can take a lot off the bill, but rarely all of it. In a 2022 release announcing its Warranty Your Way program, Lennox said: "Traditionally in the heating and cooling industry, labor has not been covered as part of the standard manufacturer's limited warranty." The same release says that to get the program's benefits, outside jurisdictions that prohibit registration requirements, "eligible equipment must be registered within 60 days of installation".
Those are one manufacturer's terms as of that release. Check your own certificate for what's covered, registration and any servicing requirement.
Access
A furnace in an open utility room is quicker to work on than one boxed into a finished basement closet. When something has to be moved to reach the part, labour goes up.
Calgary winter faults
On a condensing furnace, the condensate line can freeze in a deep cold snap if it runs through a cold garage, a crawl space or an outside wall. The drain backs up and the furnace shuts down. Thawing the line gets the heat back, but it won't stop it freezing again next cold snap. Rerouting it through heated space, or protecting the exposed section, does. Ask for both to be priced. If there's water on the floor as well, see a furnace leaking water.
What a repair quote should show
Whoever does the work, the quote should spell out:
- The failed part, and how it was identified: a test reading, an error code, what the start-up showed
- The replacement part: the manufacturer's own or a universal one
- Labour, listed apart from the part
- Warranty: whether the manufacturer's warranty covers the part
- Anything else found on the visit, kept separate from the repair you called about
- Cause or symptom: whether the repair fixes why it failed, or only what failed. A new limit switch on a furnace starved of return air, or a thawed condensate line still running through the garage, will be back.
When replacement makes more sense
A small part on a younger furnace is normally just a repair. Past that, age decides:
- A major failure on a furnace past about 18 years: strongly consider replacing it. The new part goes into a furnace where everything else is just as old.
- A major failure between about 12 and 18 years: a genuine judgement call. Get the repair and a replacement quoted side by side, and weigh them against how long you plan to stay.
- A cracked heat exchanger: replace it, at any age.
There's more in our repair-or-replace rule of thumb. Natural Resources Canada's Heating with Gas guide makes a similar point about upgrading an older blower motor: "If your furnace is nearing the end of its service life, investing in an efficient retrofit motor is probably not a wise choice."
A furnace install with us runs $4,500 to $9,600 as of September 2026, the same in Calgary and Airdrie. An old mid-efficiency furnace isn't replaced like for like: the new one is a condensing furnace, with new plastic venting and a condensate drain. The City of Calgary's plumbing and gas permits page lists a furnace replacement permit as required for "HVAC contractors completing a residential furnace replacement." The full breakdown is in what a furnace replacement costs, and Financeit monthly payments are available.

Keeping repair bills down
Many small parts show wear before they quit, and regular professional servicing is when that gets spotted. NRCan's guide lists the tasks a serviceperson should do, including "checking the condition of the furnace heat exchanger" and checking the safety controls. How often depends on your furnace, so go by the manufacturer's manual for your model. Our furnace tune-up page covers what the visit includes.
The short version
What failed sets most of the price. Age, warranty, access and whether the repair fixes the cause set the rest. On an older furnace with a major failure, get a replacement priced next to the repair.
For a free quote, call 587-834-3668 or reach us through our contact page. On timing, call and we'll tell you honestly when we can get there. North of the city, see furnace repair in Airdrie.

